Overview

  • TechControl™ Display locks in performance, and uptime
  • Set mowing turn speed to reduce scuffing
  • AutoPedal™ lowers fuel consumption and noise
  • Final Tier 4 without sacrificing horsepower

View Product Brochure

Features

MTSpiral and MTGrooved roller options for most any turf condition
    MTSpiral roller overallMTSpiral roller overall
    MTSpiral end sectionMTSpiral end section

    The MTSpiral roller and the MTGrooved roller (not shown) options are available for QA5 cutting units to minimize roller overlap marks.
     
    The MTSpiral roller and the MTGrooved roller options take the patented 2-in. (50.8-mm) machine spiral roller to a whole new level. These designs reduce the number of times the grass is rolled in the overlap area of the cutting units. With these unique designs, the material in the overlap of the roller is machined down to a smaller diameter, allowing the ends of the rear cutting unit rollers to roll through the open space of the front cutting unit rollers.

    Types of overlap marks and what causes them
    Cause of roller overlap marksCause of roller overlap marks
    Roller overlap marks - bentgrass fairwayRoller overlap marks - bentgrass fairway

    There are two types of overlap marks - reel overlap marks and roller overlap marks. It can often be difficult to determine what type of overlap marks a customer may be experiencing. In general, a roller overlap mark is roughly 3.5-in. (88.9-mm) to 4-in. (101.6-mm) wide, while a reel overlap tends to be   2.5-in. (63.5-mm) to 3-in. (76.2-mm) wide.

     

    A reel overlap mark may be caused by a variety of factors:

    • Bedknife attitude
    • Low effective height of cut
    • Frequency of clip to high (shorter distance between cuts)
    • Cutting unit not parallel
    • Bedknife to reel contact
    • Dull reel and/or bedknife
    • Turf stress

    A roller overlap mark is caused by how many times the front and rear rollers of the cutting units go over the turf. With traditional roller setups, the grass is rolled four times in the overlap of the front and rear cutting units – once by the front roller of the front cutting unit, once by the rear roller of the front cutting unit, once by the front roller of the rear cutting unit, and once by the rear roller of the rear cutting unit. 

     

    The rest of the cutting unit roller surface, not in the overlap, rolls the grass twice, once by the front roller and once by the rear roller. In certain conditions, particularly in times of lush growth, this may result in overlap marks, which will be darker striping marks in the dark stripes and lighter striping marks in the light stripes.

    How the MTSpiral roller and the MTGrooved roller minimize roller overlap marks
    Overlap design of MTSpiral rollersOverlap design of MTSpiral rollers
    Reduction of overlap marks - bentgrass fairwayReduction of overlap marks - bentgrass fairway

    The MTSpiral roller and the MTGrooved roller change the game in terms of roller overlap marks. Due to their design, at no point is the grass rolled more than twice. At every point across all five cutting units, the grass is rolled exactly two times. What this means is a more uniform appearance across the cutting pass.
     
    If a customer decides the MTSpiral roller or the MTGrooved roller is the right choice to meet the needs for their application, it is recommended that both front and rear rollers be replaced with the MTSpiral rollers, or MTGrooved rollers, to achieve optimum performance and minimize overlap marks.
     
    Since these are spiral and grooved rollers, they will tend to engage the turf more than a cutting unit setup with a smooth rear roller. A starting guideline is that all cutting units equipped with front and rear MTSpiral rollers, or MTGrooved rollers, be set up with a benchsetting of at least 0.050 in. (1.1 mm) higher to achieve a similar effective height of cut. Proper height-of-cut setting is critical for this setup.
     
    The optional MTSpiral roller or MTGrooved roller setup does not solve issues due to reel overlap marks. Height-of-cut when the MTSpiral roller or MTGrooved roller is used should be measured by placing the gauge bar approximately 4 in. (101 mm) from the end of the roller to stay away from the tapered ends.

    Applications for the MTSpiral roller and the MTGrooved roller
    Reduction of overlap marks - paspalum fairwayReduction of overlap marks - paspalum fairway
    #

    MTSpiral rollers and MTGrooved rollers can be installed on all PrecisionCut™ and E-Cut™ Hybrid Fairway Mowers and Riding Greens Mowers with QA5 cutting units. They are an addition to the lineup of roller options for fairway, tee, and approach applications, and may help reduce roller overlap marks on both warm season and cool season turfgrasses.  Use of the MTSpiral Rollers or MTGrooved rollers is not recommended for greens applications.

    Available for both the 18-in. (45.7-cm) and 22-in. (55.9-cm) cutting units, the MTSpiral roller and MTGrooved roller feature a true 18-in. (45.7-cm) and 22-in. (55.9-cm) length with tapered ends. This full-length roller, as compared to other shorter rollers in the marketplace, supports the cutting unit in turns and on sidehills without the gouging or marking.
     
    This design is only available in the 2-in. (50.8-mm) configuration at this time:

    • BM23566 – 2-in. x 22-in. (5.1 cm x 55.9 cm) MTSpiral roller
    • BM23567 – 2-in. x 18-in. (5.1 cm x 45.7 cm) MTSpiral roller
    • BTC10267 - 2-in. x 22-in. (5.1-cm x 55.9-cm) MTGrooved roller
    • BTC10281 - 2-in. x 18-in. (5.1-cm x 45.7-cm) MTGrooved roller
eHydro™ hydrostatic pump and large-capacity wheel motors for serious hill-climbing capabilities
    Large wheel motorsLarge wheel motors
    eHydro™eHydro™

    The eHydro™ traction pump and wheel motors in the new A-model takes performance, traction, and operation to the next level.

     

    We designed the new system to take on the most challenging course conditions. These improvements to the traction system makes the A-models ideal for undulating terrain providing superior performance and traction out on the course.

     

    The traction system in the A-models is driven by a servo-controlled hydrostatic pump. The control of the pump is no longer mechanical linkages but instead it is electronic.

     

    In total approximately 94 parts have been eliminated from the traction drive system along with 4 adjustments compared to prior models. The design reduced the complexity of the drive system meaning no more linkages to adjust or repair decreased routine maintenance and providing reliable day-in/day-out operation.

    Forward/reverse pedalsForward/reverse pedals
    #

    The operator will like the eHydro, too. The pedal effort has been reduced, thus reducing the foot fatigue during many hours of mowing.

GRIP All-Wheel Drive Traction System provides superior traction by reducing wheel slip
    Optional GRIP all-wheel driveOptional GRIP all-wheel drive
    #

    For superior traction with a true hydraulic four-wheel drive (4WD), the GRIP All-Wheel Drive Traction System is optional equipment for the PrecisionCut™ and E-Cut™ Hybrid fairway mowers. This system reduces wheel slip by sending flow from the front wheel to the opposite rear wheel.

    For example, if the front right wheel starts to slip, hydraulic flow is diverted to the left rear wheel to maintain positive traction. By allowing the flow to cross over to the opposite rear wheel, the system maintains traction not only while climbing straight up hills, but also on side hills, as well. 

    The GRIP All-Wheel Drive Traction System is always engaged when driving forward with the PrecisionCut and E-Cut Hybrid fairway mowers. There are no electronics to engage the 4WD system, simplifying the electrical system and the design of the valve at the rear of the machine.

    In reverse, a standard switch is provided that disengages 4WD. The switch senses that the reverse pedal has been depressed and shuts off flow to the rear drive wheels. This ensures that the front drive tires are doing the work in reverse rather than the rear tires, minimizing wheel slip and scuffing of turf when backing up an incline.

Larger, 63.5-mm (2.5-in.) front grooved disc roller compatible with Fairway Tender Conditioner (FTC) and Greens Tender Conditioner (GTC) attachment for 22 In. (55.9 cm) Quick Adjust 5 reel cutting units
    Grooved disc rollerGrooved disc roller

    The grooved disc roller can be used with 55.9-cm (22-in.) Quick-Adjust 5 (QA5) cutting units, in combination with the GTC and FTC, to provide additional roller options for fairway, tees, and approach areas.

     

    The increased diameter improves the durability over smaller rollers and it features hardened discs for improved wear which retains spring tension for reduced maintenance, making it an ideal roller for fairway, tee, and approach mowing.

Easily accessible daily service points mean less maintenance time and more time working
    Easy access for cleaningEasy access for cleaning

    Easier daily maintenance points are designed into the machine to assist operators with complete daily maintenance and to keep the machine running at peak performance, saving valuable time and money.

     

    For ease of service, all daily engine checks are easily accessible by raising the hood. These service points include an engine-oil level check, a coolant level check, hydraulic fluid level, and an air-restriction indicator.

     

    The A-model PrecisionCut™ Mowers, E-Cut™ Hybrid Mowers, and TerrainCut™ Mowers feature a radiator screen easily removed without tools and tilt-out oil cooler for easy cleaning.

Electric reel drive system eliminates all potential leak points in the reel circuit
    Electric motors drive cutting unitsElectric motors drive cutting units
    #

    Ninety percent of all hydraulic leaks occur in the reel hydraulic circuit, mainly due to the necessity of having flexible hoses extending from the front of the machine for the front reels.

     

    These hoses see a lot of flexing during the mowing day as cutting units are raised and lowered. Cutting units also steer and float to follow undulations, increasing fatigue for the reel motor hoses.


    The 7500A and 8000A E-Cut™ Hybrid Fairway Mowers have eliminated all reel circuit leak points by removing all hydraulics from the cutting unit drive circuit.


    This has eliminated the following hydraulic components:

    • Reel drive section of hydraulic triple pump
    • Hydraulic reel motors
    • Backlapping valve
    • Flexible hoses
    • Fittings
    • Hard lines

    Fewer hydraulic components leads to fewer leaks, increasing confidence that the finely manicured turf will not be damaged by hot hydraulic oil spilled onto a playing surface before an important tournament. 

Reduced sound levels and fuel consumption at 2300 rpm
    Reel circuit power source 180-amp alternatorReel circuit power source 180-amp alternator
    Electric motors drive cutting unitsElectric motors drive cutting units

    The E-Cut™ Hybrid Fairway Mowers are unique in that electrical power is used to minimize hydraulic leak opportunities in the reel circuit, but an engine is utilized to ensure optimal performance throughout the day. This presents an opportunity to further enhance machine performance through reduced sound levels and improved fuel savings, by running the machine at less-than-full throttle. When running the E-Cut Hybrid machines at the recommended reduced setting it does not sacrifice cut quality as the reel speed is still maintained at approximately 2200 rpm.

    Mow engine speed screenMow engine speed screen
    Password-protected settingsPassword-protected settings

    This reduced throttle setting is set quickly and easily using the TechControl display. Simply use the    password-protected mower set-up screen Engine Mow Speed to set maximum engine speed while in mow. Once set, the engine speed automatically uses this rpm when the machine is mowing. This allows complete control of sound levels and fuel savings.

     

    The 7500A and 8000A E-Cut™ Hybrid Fairway Mowers can be effectively run in mow at an engine rpm reduced to 2300 rpm. At this operating rpm, operators will experience noise reductions when compared to running the machines at full throttle.

     

    In addition to the reduced sound levels, the operation at this engine rpm will reduce fuel usage due to slower engine rpm. Comparisons have shown that, depending on conditions and usage, fuel savings can be as high as 30 percent when running the machine at 2300 rpm as opposed to running at full throttle required by traditional hydraulic machines.

TechControl display maximizes performance and uptime by allowing more control in operation and diagnostics
    TechControl displayTechControl display
    Password-protected settingsPassword-protected settings
    Now there is more control with the TechControl display with a large easy-to-read screen

    Passcode-protected TechControl display enables quickly setting or changing mowing speed, turning speed, or transport speed to limit variations in performance by different operators.

    Mow setting screenMow setting screen

    Quickly adjust the mow or transport speed to make sure mow speed is what is needed for the changing conditions. The setting can be adjusted precisely using a speedometer app on a smartphone or GPS device.

    Turn-speed setting screenTurn-speed setting screen

    Use the TechControl to slow the machine during turns while mowing and protect against turf scuffing and aggressive turning operators.

     

    The turn speed control engages when in mow and the cutting units are lifted for turns. Once the turn is made and the cutting units are lowered, the machine speed returns to the set mow speed.

     

    The turn speed is a percentage of mow speed. When set to 100 percent, turn speed control is off or allows 100 percent of the mow speed in turns. Turn speed setting of 50 percent allows only 50 percent of the set mow speed to be reached during turns.

     

    Here is an example:

    Mow speed = 6 mph (9.66 km/h)
    Turn speed set at 50 percent
    Maximum turning speed will be 3 mph (4.83 km/h)

    Input/output screenInput/output screen
    Service timers screenService timers screen

    The A-model PrecisionCut™ Mowers, E-Cut™ Hybrid Mowers, and TerrainCut™ Mowers have the latest in advanced diagnostics through the TechControl display. Most all diagnostics are performed while sitting in the operator’s seat.

     

    The TechControl has onboard visual diagnostics allowing quick and easy machine diagnostics, maximizing up time. The system allows technician to see inputs and outputs of the electrical system.  Also, the technician can see stored controller codes on the machine to aide in troubleshooting incidents that may have occurred while on the course.

     

    The TechControl will also display the notification for maintenance of the hydraulic and engine oils using service timers to notify when it has reached the time to perform the required service.

    Language settingsLanguage settings
    #

    Choose from a list of several languages to use for the TechControl.

     

    Operator warning notifications are incorporated into the TechControl and will alert the operator if a problem arises during operation.

     

     

    Description

    Hydraulic over temp

    Hydraulic oil filter restriction

    Engine oil pressure low

    Engine coolant temperature

    Reel motor

    Battery voltage

Tires sized for proper weight distribution and a low ground pressure
    Front tireFront tire

    When considering a fairway mower's effects on turf compaction, there is more to it than just weight alone. Weight is only a small factor in determining turf compaction.

    A key component is the selection of tires used on the machine involves both sizing and tread patterns. The John Deere PrecisionCut™ and E-Cut™ Hybrid Fairway Mowers use large, 26x14-12 front tires for proper front weight distribution, and 20x10-8 tires in the rear to distribute the rear weight.

    Both tires use a turf tread to maximize turf friendliness.

    They excel in weight distribution providing low ground pressure onto the turf. This provides less tracking, less marking, and less compaction.

Cutting units are stable and fold inside the front tires for easy transporting
    Rubber mounted front up stopsRubber mounted front up stops
    Double rear up stopDouble rear up stop

    The 7500A, 7700A, 8700A PrecisionCut™ and 7500A E-Cut™ Hybrid Fairway Mowers all have cutting units that contact up stops for transport. These up stops are rubber and limit cutting units from swinging during transport.  The lift system also folds the two wing units inside the tires to limit possibility of damage to the wing units when transporting through and around objects on the course.

AutoPedal™ feature lowers sound levels and fuel consumption during transport
    AutoPedalAutoPedal
    #

    The AutoPedal feature controls engine rpm and transport speed of the machine through the eHydro™ foot pedal controls. AutoPedal is similar to an automobile gas pedal operation; the more the forward pedal is pressed, the faster the machine moves and the higher the engine rpm; pressing the pedal less, the slower the machine moves and the lower the engine rpm.

     

    On conventional machines, the engine rpm is controlled by the operator by means of a manual or electric/manual throttle. Operators are trained to always operate the engine at wide-open throttle. Running at wide open throttle means running the engine at its fastest speed, which increases the sound levels and fuel usage.

     

    The AutoPedal system allows the engine to only run as fast as needed, meaning that as operators transport around the course, the engine speed is only as fast as needed for the transport speed. If the operator approaches play and stops, the engine rpm goes to idle. This makes transporting quieter and since the engine does not run full speed all the time, it reduces fuel consumption.

     

    Once the operator reaches the mowing site, engages the mow switch on the CommandARM™ controls, the engine rpm automatically increases to full throttle for mowing.

Double-acting, single-rod hydraulic steering cylinder for lines as straight as a greens mower
    Steering cylinder and linkage systemSteering cylinder and linkage system

    Ever wanted stripes as straight as they are on the greens? The A-Model PrecisionCut™ Mowers and E-Cut™ Hybrid Mowers do exactly that. Utilizing the same style steering cylinder as on the 2500B PrecisionCut and 2500E E-Cut Hybrid Riding Greens Mowers, the PrecisionCut and E-Cut Hybrid Mowers can mow the straightest lines of any mower in the industry today.

     

    Traditional hydraulic cylinders have a rod on only one side of the cylinder. The cylinder on the A-models has one rod that goes through both sides of the cylinder. This equalizes volume and pressure on both sides of the cylinder packing, helping the operator make perfectly straight lines with little effort.

     

    This system also equalizes the steering effort, meaning easy turns whether turning to the right or to the left.

48-V, 180-amp alternator powers reel drive motors, requiring no additional batteries on unit
    48-V 180-amp 48-V 180-amp
    #

    The reel circuit is powered by a 48-V, 180-amp alternator belt-driven by the engine. The alternator supplies constant power to the reel circuit and only generates 48 V when the mow system is engaged.

     

    Due to this design, no additional batteries are required to drive the reel motors on the 7500A and 8000A E-Cut™ Hybrid Fairway Mowers. With traditional electrical mowing systems, the frequency of clip would change as the batteries drained while mowing.

     

    A battery pack begins to lose its power immediately when used, but not on the E-Cut Hybrids. Since they still use an engine to drive an alternator, the frequency of clip at the start of the day and at the end of the day is exactly the same, yielding unparalleled quality of cut from start to finish.

     

    Plus, the machine doesn't have to be plugged in to charge the batteries once the day's mowing is done.  The only limitation on run time with the E-Cut Hybrids is making sure the operator starts the day with a full fuel tank, just like with any other gas- or diesel-powered machine on the market today.

     

    The alternator only supplies power to the reel circuit. The remainder of the circuits are powered by a 12-V battery.

Brushless electric reel motors for compact design and optimal efficiency
    Reel motorsReel motors

    The electric reel motors on the 7500A and 8000A  E-Cut™ Hybrid Fairway Mowers are brushless, allowing them to be compact in size, roughly equal to that of today's hydraulic reel motors. The brushless motors are very efficient, leading to years of optimal performance with very minimal maintenance, and sealed for protection from the elements.

    The motors are bidirectional and variable speed, meaning they can spin forward or reverse and at a range of rotational speeds. The motors spin forward for mowing operations and backward for backlapping operations.

     

    A poly-chain belt connects the motor shaft to the reel and rotates the reel when the cutting units are engaged. The internal components of the motor are sealed for long life, durability, and protection from the elements.

     

    Cutting units are easily removed from the cutting unit motors by loosening the two bolts securing the motor to the cutting unit, turning the motor approximately a quarter turn, and pulling the motor from the cutting unit. This can be done in a matter of seconds. A tether prevents damage to the wiring harness when the motor is removed.

Specifications

Engine

  • Type Direct Inject Turbocharged Diesel
  • Compliant emission regulation United States and Canada Tier 4
  • Horsepower Maximum rated horsepower
    At 2800 rpm ISOC: 31 kW
    41.6 hp
  • Cylinders Three
  • Displacement 1.568 L
    95.69 cu in.
  • Air cleaner 2-stage dry element
  • Fuel Diesel
  • Cooling system Liquid centrifugal pump; forward machine location for optimum cooling

Vehicle

  • Drive pump Tandem gear pump
  • Hydraulic system capacity 45.4 L
    12 U.S. gal.
  • Fuel tank capacity 60.6 L
    16 U.S. gal.
  • Steering Hydraulic power with double acting steering cylinder
  • Front drive tires 26.5x14-12 turf
  • Steering tires 20x12X10-8 turf
  • Ground pressure 69 kPa
    10 psi
  • Brakes Internal hydraulic wet disc brakes with dynamic braking through closed loop hydrostatic system
  • ROPS Standard; meets ISO 21299 Standard

Operating weight

  • Cutting units lowered 1166 kg
    2570 lb

Controls

  • Throttle Automatic controls with AutoPedal foot controls; manual control through TechControl display
  • Forward/reverse 2-pedal
  • Mower lift One-touch single handle
  • Parking brake Electric Switch on Command Arm for Internal Wet Disk Brakes
  • Seat Suspension seat with seat belts and arm rest; fore/aft adjustment; weight and lumbar adjustment
  • PTO Electric Switch on Command Arm
  • Tilt steering Left Foot operated for easy adjustment

Dimensions

  • Height with ROPS 224 cm
    88 in.
  • Length 323 cm
    127 in.
  • Transport width 221 cm
    87 in.
  • Mowing position width 287 cm
    113 in.
  • Ground speed Mowing
    0 to 12.8 km/h
    0 to 8.0 mph4WD mow speed
    0 to 12.8 km/h
    0 to 8.0 mphTransport
    0 to 18.5 km/h
    0 to 11.5 mphReverse
    0 to 6.4 km/h
    0 to 5.0 mph

Cutting Units

  • Number Five
  • Size Quick Adjust QA5: 55.9 cm
    22 in.
  • Total width of cut 254 cm
    100 in.
  • Height of cut Construction
    2.0 to 28.5 mm
    0.078 to 1.125 in.
  • Frequency of clip (FOC Reels) or Blade tip speed (decks) Rollers
    Front and rear: 51 mm
    2 in.
    Optional: 76.2 mm
    3 in.
    11 Blade: 0.69 mm/km/h
    0.044 in./mph
    7 Blade: 1.09 mm/km/h
    0.069 in./mph
  • Reel diameter 12.7 cm
    5 in.

Sound levels

  • Measuring standard ISO 11201
  • Attachments installed FTCs, reels engaged

Fuel economy

  • Actual fuel usage will vary depending on course conditions, operation, turf and fuel quality 25% load: 2.8 L/hr
    0.75 gph
    40% load: 4.32 L/hr
    1.14 gph
    50% load: 5.22 L/hr
    1.38 gph

Warranty

  • Type Two-year limited

Certification

  • Type ANSI B71.4-2012.

Mexico

573-581-5900

Macon

660-385-2177

Rocheport

573-446-3030

Kirksville

660-665-1500

Chillicothe

660-646-5493

Palmyra

573-769-2112

Moscow Mills

636-366-9400

Curryville

573-594-6493

Tipton

660-433-5596

Hermann

573-486-3204

Dutzow

636-433-2256

SALISBURY

660-388-6166
Your Partner In Growing A Better Tomorrow
ABOUT USCONTACT US | CAREERS | BLOG | SPECIALS | SITEMAP | POLICIES | DONATION REQUEST |
AG EDUCATION PARTNERSHIPS | EQUIPMENT TRANSFER REQUEST


Copyright ©2017 Sedona Technologies. All rights reserved.