Overview

  • Greatly reduce triplex ring with exclusive offset cutting units
  • Save time with Quick Adjust Cutting Units
  • Exceptional contour-following and steering of cutting units in turns
  • On-board diagnostics

View Product Brochure

Features

Easy service access to minimize time to perform daily maintenance tasks
    Daily service checksDaily service checks
    Access panelAccess panel

    Several serviceability features were incorporated into the design of the 2500B PrecisionCut™ Riding Greens Mower to make routine checks and adjustments as easy as possible.

    Features include:

    • Good visibility to components, with a tilt-back hood and tilt-up seat platform. With the hood and seat platform in the raised position, access and visibility to the components underneath is very good.
    • All daily service checks — engine oil level, air restriction indicator, engine coolant level, and hydraulic oil level — are made from the left side of the machine.
    • Quick-attatch cutting units — one pin located at the front of the lift arms removes the cutting units from the traction unit with no tools.
    • Quick-attatch cutting unit motors — just loosen the two hold-down nuts, twist the motor, and pull it out away from the cutting unit.
    • Remote grease fittings for the front lift arms are located on the front hydraulic fitting bulkhead. These remotely mounted fittings allow ease of lubrication for the front lift arm pivot pins.
    • Electronic controller that provides service diagnostics by means of lighted circuits.
    • There is also an access panel on the operator platform that can be easily removed to provide access to the backlap valve and battery.
Operator storage area easily accessed from either side of machine
    Found behind operatorFound behind operator
    Larger capacityLarger capacity
    Access from both sidesAccess from both sides

    Operator storage area is located behind the operator for easy access from either side of the machine.  This large storage area is design to hold items such as jackets or other items that may be needed by the operator. 

Standard rollover protective structure (ROPS) with seat belts meets ISO 21299 standards
    ROPS with seat beltROPS with seat belt

    A ROPS and retractable seat belt are standard equipment on both the 2500B PrecisionCut™ and 2500E E-Cut™ Hybrid Riding Greens Mowers. The ROPS meets ISO21299 standards.

Smooth and turf tire options to meet a variety of mowing conditions and areas
    Smooth and turf tire options shownSmooth and turf tire options shown
    Balloon-rounded tire optionBalloon-rounded tire option

    There are four tire options:

    • 18x10.50-10 2-ply smooth tires are recommended for those who want the minimum amount of ground compaction. These tires have a large footprint to spread the weight of the vehicle over a larger area. This tire also lowers the overall height of the machine and reduces ground clearance of the cutting units. Compensation for ground clearance can be made by adjusting the cutting unit chain on the back of the cutting unit.
    • 20x10-10 4-ply rated balloon-rounded smooth tires are recommended for those who want maximum ground clearance, increased ply rating and desire to use a more rounded tire. The 4-ply side wall rating has recommended operating tire pressure of 103 kPa (1.03 bar) (15 psi). Increased pressure may leave marks in softer turf conditions.
    • 20x10-10 2-ply smooth tires are recommended for those who want maximum ground clearance while operating at the lower tire pressure of 83 kPa (0.83 bar) (12 psi).
    • 20x10-10 4-ply rated smooth tires are recommended for those who want maximum ground clearance and increased ply rating. The 4-ply sidewall rating has recommended operating tire pressure of 103 kPa (1.03 bar) (15 psi). Increased pressure may mark in softer turf conditions.
    • 20x10-10 turf tires are for those who need additional traction for mowing more difficult areas, such as elevated tees or fairways.

     

    Each of these tire options includes a complete set of three tires and wheels that are all the same size. (This includes the turf tires, which come as a set of three treaded tires.)

Easy access fuel tank with fuel gauge keeps operator productive
    Fuel gauge and filler capFuel gauge and filler cap
    Twin-sheet design fuel tankTwin-sheet design fuel tank

    The fuel tank is a twin-sheet design to and meets fuel tank regulatory requirements and still has the capacity to get through a normal day without refueling. Easy access to the fuel cap and clear view of the fuel gauge keeps the operator productive all day.

Optional weight transfer grass-catcher system transfers clipping weight to frame, rather than to cutting unit

    Most golf courses want to mow the greens and collect the grass for a premium cut and even and smooth appearance. The most challenging concern with catching grass with a greens mower is that as the grass catcher fills with material, its weight is transferred to the cutting unit. This problem is multiplied with a riding greens mower because there are three cutting units and grass catchers collecting different amounts of grass, meaning different weights are applied to the three cutting units.

     

    If the weight cannot be removed from the grass catchers, the different weights can cause different heights of cut with each cutting unit, leaving poor playing conditions and after-cut appearance. This is especially noticeable through undulations of a green and on the clean-up pass. The grass catchers on the riding greens mowers have been designed for optimum catching efficiency while maintaining a consistent, effective height of cut.

    Grass catcher clip (1) and lift arm bracket (2)Grass catcher clip (1) and lift arm bracket (2)

    The exclusive John Deere grass catcher transfers approximately two-thirds of the weight to the vehicle's lift arm. This helps maintain a more-consistent cutting height to ensure a uniform cut across all three cutting units.

     

    The front grass catchers can be removed and installed with one hand because of an innovative clip system. The clip secures the catcher to an adjustable bracket on the lift arm, transferring weight from the catcher to the lift arm as clippings accumulate in the catcher.

    Rear grass catcher (1) and bail system (2)Rear grass catcher (1) and bail system (2)

    The rear grass-catcher mounting system simplifies removal and installation of the rear grass catcher and reduces effort.

     

    The retaining-bail system for the rear grass catcher also uses the exclusive John Deere design to transfer the weight of the grass catcher to the lift arm.

    Rear grass catcherRear grass catcher

    The grass catcher can be easily removed, without spilling the clippings, by rotating the grass catcher back toward the front of the machine until the front grass catcher lip is above the cutting unit side plate. Then, simply pull it out to the side. This can be accomplished with the cutting unit in the raised or lowered position.

    Grass catcher channelGrass catcher channel

    A channel in the cutting unit side frames guides the grass catcher onto the cutting unit. The channel in the castings ensures the grass-catcher lip maintains its relationship with the cutting unit when following undulations, providing for better grass-catching efficiency.

    Adjustable top shieldAdjustable top shield

    Adjustable cutting-unit top shields also ensure that grass is thrown into the back of the catcher, even as the reel diameter decreases due to wear. The catchers are shaped and vented to allow the air from the reel to escape while retaining the clippings.

    Top-shield extension for dry conditionsTop-shield extension for dry conditions

    Extensions for the cutting-unit top shields are for use in dry conditions to maximize the flow of dry clippings into the grass catcher. If mowing predominantly in wet-turf conditions, remove the cutting unit shield extensions to reduce buildup and accumulation of clippings on the front of the grass catcher.

Offset cutting units virtually eliminate triplex ring with a simple change in direction
    Offset cutting unitsOffset cutting units

    The innovative offset design staggers wheel tracks in the cleanup cut by simply changing direction of travel each day. This allows the turf an additional day to recover before being driven over again, and serves to minimize triplex ring and compaction.

    The cutting units offset to the left-hand side of the machine. This provides good visibility to the center cutting unit. The traction unit frame is designed to maximize visibility down the left-hand side of the machine from the operator's point of view.

Optional direct mount front grass-catcher system easy to install and remove

    The optional direct mount front grass catchers provide the choice of systems to meet the needs on your golf course.

    #

    The grass catcher is mounted directly to the front cutting unit using a similar design as the SL Walk Greens Mowers.

    This provides quick access for the removal and installation of the grass catcher as well as superior ground following and collection due to position of the catcher to the cutting unit.

    It is recommended that catchers be emptied after each green during normal and heavy growth times to reduce weight on the cutting unit.

    The direct mount grass catchers will fit model year 2009 to current 2500B and 2500E E-Cut Riding Greens Mowers with Quick-Adjust 5 (QA5) cutting units.

    Rear grass catcher (1) and bail system (2) Rear grass catcher (1) and bail system (2)

    The rear grass-catcher mounting system simplifies removal and installation of the rear grass catcher and reduces effort.

    Rear grass catcherRear grass catcher

    The grass catcher can be easily removed without spilling the clippings by rotating the grass catcher back toward the front of the machine until the front grass catcher lip is above the cutting unit side plate. Then, simply pull it out to the side. This can be accomplished with the cutting unit in the raised or lowered position.

    Adjustable top shieldAdjustable top shield

    Adjustable cutting-unit top shields also ensure that grass is thrown into the back of the catcher, even as the reel diameter decreases due to wear. The catchers are shaped and vented to allow the air from the reel to escape while retaining the clippings.

    Top-shield extension for dry conditionsTop-shield extension for dry conditions

    Extensions for the cutting-unit top shields are for use in dry conditions to maximize the flow of dry clippings into the grass catcher. If mowing predominantly in wet-turf conditions, remove the cutting unit shield extensions to reduce buildup and accumulation of clippings on the front of the grass catcher.

14-blade reel lowers frequency of clip
    14-blade reel14-blade reel
    #

    Using the 14-blade reel on greens mowers will lower the frequency of clip and also provide a clean, smooth cut. It can increase the playability of the putting surface and greens speed.

     

    Frequency of clip (FOC) is defined as the distance traveled between consecutive cuts. In other words, it is how far the machine moves from the time one blade passes across the bedknife until the next blade passes. The lower the frequency of clip, the less distance that is traveled until the next blade passes.

     

    There is a point of diminishing returns when it comes to frequency of clip. The less distance the mower travels between consecutive cuts, the more times the same grass blade is going to be impacted by the reel. Too low a frequency of clip can cause bruising of the turf - especially in the overlap from pass to pass.

     

    Frequency of clip is often used as a measurement of cut quality, however there are other key factors that attribute to gaining good quality of cut. The factors that lead to good cut quality are:

    • Geometry of the cutting unit
    • Sharpness of reels and bedknife
    • Proper cutting-unit setup (parallel and bedknife-to-reel clearance)
    • Height of cut (HOC) (effective versus bench HOC)
    • Bedknife selection
    • Roller selection for the turf conditions
    • Turf conditions

    The geometry of John Deere cutting units makes the optimum range for frequency of clip between 0.160 in. (4.064 mm) and 0.190 in. (4.824 mm) for walk greens mowers. This is where the technology of the PrecisionCut™ walk greens mowers excels and provides a superior cut and after-cut appearance.

    Machines

    14-blade reel part number

    Minimum FOC
    in. (mm)

    Minimum FOC with AMT2865*
    in. (mm)

    180SL PrecisionCut Walk Greens Mower

    TCA23624

    0.141 (3.58)

    0.123 (3.12)

    220SL PrecisionCut Walk Greens Mower

    TCA23623

    0.141 (3.58)

    0.123 (3.12)

    *Frequency speed-up kit
Larger, 63.5-mm (2.5-in.) front grooved disc roller compatible with Fairway Tender Conditioner (FTC) and Greens Tender Conditioner (GTC) attachment for 22 In. (55.9 cm) Quick Adjust 5 reel cutting units
    Grooved disc rollerGrooved disc roller

    The grooved disc roller can be used with 55.9-cm (22-in.) Quick-Adjust 5 (QA5) cutting units, in combination with the GTC and FTC, to provide additional roller options for fairway, tees, and approach areas.

     

    The increased diameter improves the durability over smaller rollers and it features hardened discs for improved wear which retains spring tension for reduced maintenance, making it an ideal roller for fairway, tee, and approach mowing.

Consistent height of cut through contour following, weight transfer, and cutting-unit suspension
    Lift-arm designLift-arm design

    The cutting-unit suspension and lift arms are designed with down stops for the lift arms to rest on when the cutting units are lowered to mow. This transfers the weight of the lift arms onto the traction unit frame rather than adding weight to the cutting unit.

    Ball-joint mounting designBall-joint mounting design

    The cutting-unit mounting system has a ball-joint swivel designed to allow the cutting unit to float independently of the lift arm. This design minimizes scalping and promotes a consistent height of cut by allowing the cutting unit to easily follow ground contours and steer in turns.

     

    The cutting units can be easily and quickly removed from the lift arms by pulling the quick pin located behind the ball swivel joint and disconnecting the cutting unit support chain from the lift arm. This disengages the cutting unit assembly from the lift arm for service.

     

    The cutting-unit drive motor also has a Quik-Tatch system that allows the technician to quickly remove the motor from the cutting unit for service. Simply loosen the mounting bolt that secure the motor to the bearing housing and twist the motor a quarter turn to remove.

Quiet and powerful diesel engine
    Diesel engineDiesel engine

    The 2500B PrecisionCut™ and 2500E E-Cut™ Hybrid Riding Greens Mowers use a 19.6 hp* (14.6 kW) gross (per SAE J1995 at 3000 rpm) liquid-cooled diesel engine for smooth, efficient, and quiet operation.

     

    With the 3-cylinder diesel engine and a large 7.9-U.S. gal. (29.9-L) fuel tank, the 2500B and 2500E give the operator power and fuel for a productive day of mowing.

     

    *Engine horsepower and torque information are provided by the engine manufacturer to be used for comparison purposes only. Actual operating horsepower and torque will be less. Refer to the engine manufacturer’s website for additional information.

Specifications

Engine

  • Type Diesel model
    IDI Diesel
  • Horsepower Diesel horsepower
    Per SAE J1995: 14.6 kW
    19.6 hp
    *Engine hp is provided by the engine manufacturer to be used for comparison purposes only. Actual operating hp will be less. Refer to the engine manufacturer?s web site for additional information.
  • Air cleaner Semi-cyclone, dry-type, dual stage
  • Cooling Oil filter
    Full-flow filterEngine oil capacity
    With filter: 2.6 L
    3.1 U.S. qtPressurized lubrication system
    StandardNumber of cylinders
    3-cylinderDisplacement
    784 cc
    47.8 cu in.
    Liquid

Electrical System

  • Charging system Flywheel, alternator
  • Alternator capacity 20 amp
  • Battery type BCI group 40 maintenance-free: 12 V
  • Starter Electric (solenoid shift)

Vehicle Specifications

  • Wheels and tires Front/rear
    18x10.5-10, 2-ply, smooth (low compaction); 20x10-10, 2-ply, smooth; or 20x10-10, 2-ply, turf
  • Brakes Type
    Dual, 15.2 cm
    6 in.
    Single-pedal, 2-wheel disc brakes
  • Mowing speed Adjustable mow stop: 0-6.4 km/h
    0-4 mph
  • Transport speed 0-13.7 km/h
    0-8.5 mph
  • Reverse speed 0-4.8 km/h
    0-3 mph
  • Ground clearance with catcher 10.2 cm
    4 in.
  • Fuel tank capacity In a single tank: 29.9 L
    7.9 U.S. gal.
  • Muffler Horizontal discharge below frame
  • Hydrostatic drive system capacity 28.8 L
    7.6 U.S. gal.
  • Hydraulic reservoir capacity (only) 20.4 L
    5.4 U.S. gal.
  • Ground drive, reel drive Drive wheels
    FrontTraction drive
    Hydrostatic, 2-pedal controlReel drive
    Hydraulic
  • Pump 3-section gear
  • Reel control valves Electro-hydraulic, one valve reel on-off and one valve raise-lower
  • Filtration 10-micron

Operator Controls

  • Steering Hydrostatic, adjustable steering column
  • Reel drive and reel lift Right-hand operated (optional foot-lift controls)
  • Throttle Right hand
  • Park brake Right foot
  • Hydrostatic speed control Forward
    Right footReverse
    Right foot
  • Ignition Key start and shutoff
  • Glow plug switch and indicator light Automatic, on instrument panel

Instrumentation

  • Engine oil pressure LED Warning Light
  • Alternator LED Warning Light
  • Hydraulic oil temperature LED Warning Light
  • Engine coolant temperature LED Warning Light
  • Hourmeter Digital

Weights and Dimensions

  • Wheelbase 129.5 cm
    51.0 in.
  • Tread width 101.5 cm
    40.0 in.
  • Mowing position width 157.5 cm
    62.0 in.
  • Turning radius, uncut circle 45.7 cm
    18 in.
  • Weight (full fluids, no operator or fuel) 637.3 kg
    1405 lb
  • Height With ROPS: 195.6 cm
    77 in.

Cutting Units

  • Number 3 - offset design
  • Size, in. (cm) Quick Adjust QA5 floating: 55.9 cm
    22 in.
  • Backlapping Standard on-board micro-backlapping and reel speed control
  • Clip frequency For 14 blade: 0.541 mm/km/h
    0.034 in./mph
    With 11-blade reel: 0.689
    0.044 in./mph
    With 7-blade reel: 1.082 mm/km/h
    0.069 in./mph
  • Front rollers Optional smooth, grooved, or spiral: 5.1 cm
    2 in.
  • Reel diameter 12.7 cm
    5 in.
  • Bedknife adjustment Bedknife-to-reel
  • Height of cut 2.0-19.0 mm
    0.078-0.75 in.
    with front roller: 51 mm
    2 in.
    or 16-32 mm
    0.625-1.25 in.
    with frotner roller: 76 mm
    3 in.
  • Number of blades 7 or 11 blades
  • Mower lift (1) cylinder for front two units; (1) cylinder for rear unit
  • Reel speed Adjustable

Certification

  • Number ANSI B71.4-2004
  • ROPS 2-Post SAE J21294 Roll Over Protection Structure with seat belts meets ISO 21299 standards
  • Engine EPA Tier 2, Interim Tier 4

Sound Levels

  • Operator ear 82 dBA
  • Measuring standard ISO 11201
  • Attachments installed GTCs and Power Brushes, reels engaged

Mexico

573-581-5900

Macon

660-385-2177

Rocheport

573-446-3030

Kirksville

660-665-1500

Chillicothe

660-646-5493

Palmyra

573-769-2112

Moscow Mills

636-366-9400

Curryville

573-594-6493

Tipton

660-433-5596

Hermann

573-486-3204

Dutzow

636-433-2256

SALISBURY

660-388-6166
Your Partner In Growing A Better Tomorrow
ABOUT USCONTACT US | CAREERS | BLOG | SPECIALS | SITEMAP | POLICIES | DONATION REQUEST |
AG EDUCATION PARTNERSHIPS | EQUIPMENT TRANSFER REQUEST


Copyright ©2017 Sedona Technologies. All rights reserved.