Overview

  • 54-row planting width on 90-ft. toolbar
  • Row spacing options: 20, 22, 30 in
  • Equipped with MaxEmerge™ 5 twin row-units
  • 3- and 5-section frames

View Product Brochure

Features

DB fertilizer options

    Option code 2627 contains a ground-driven pump, plumbing to a manifold, and routing to each row-unit. The row-unit routing allows for fertilizer delivery in front of the seed, or seed tube. Option code 2627 is not compatible with ExactEmerge™ planters because it would place fertilizer in front of the BrushBelt™ system.

     

    Option code 2628 contains a ground-driven pump plumbing to manifold and plumbing to each row-unit with a coil of hose. This option code requires either dealer or operator installation of fertilizer delivery components, such as BA32912.

     

    Option code 2629 includes a ground-drive frame and tire with drive sprocket. This option does not include a pump, manifold, or fertilizer delivery components.

Central Commodity System (CCS™) seed delivery system
    CCSCCS
    #

    CCS seed delivery adds productivity through increased seed capacity, bulk fill capability, and easy, thorough cleanout.

     

    The two tanks have a combined capacity of 2470 L (70 bu) on 9-m (30-ft) planters and 3520 L (100 bu) on 12-m (40-ft) and larger planters. CCS tanks are manufactured using a rotomolded, polyethylene design to ensure maximum durability. The translucent tanks allow easily viewing the amount of seed in the tanks. The tanks are separated by 55 cm (21.5 in.) for enhanced rear visibility during transport and backing.

     

    The following crops can be planted with CCS: corn, sweet corn, popcorn, cotton, sunflowers, sugar beets, soybeans, and sorghum (milo).

     

    Filling the tanks is convenient due to a central filling location. The staircase and railing provide access to the filling platform between the tanks. If filling the tanks with an auger, minimum recommendations are a 15-cm (6-in.) diameter, 4.3-m (14-ft) auger. Each tank has an adjustable, bin-level sensor to alert the operator when it is time to fill.

     

    A standard fill light package is available on machines equipped with CCS. This feature includes two lights conveniently mounted on the railings of the machine. The lights are turned on and off with their own switch located at the bottom of the staircase.

     

    If the seed-carrying vehicle requires hydraulic power to run the unloading system, the auxiliary hydraulic coupler option is available. These couplers are located at the bottom of the staircase and can be coupled under pressure. The system has a separate system filter that ensures your planter hydraulic system remains free of contaminates.

    Seed delivery process

    CCS is about reducing the time spent filling the planter with seed while maximizing the time spent planting. CCS for planters is a form of seed handling and delivery. The row-units perform the final task of seed metering and placement.

     

    The CCS seed delivery process relies on a hydraulically-driven fan to move seed from the CCS tanks to the row-units. This fan is plumbed in to the planter's raise/lower circuit, so only one selective control valve (SCV) is needed for both functions. When the planter is lowered, lift cylinders bottom out and hydraulic flow is diverted to the seed delivery fan. A flow control valve and gauge, located near the tank, allows for the proper tank pressure setting based on seed type.

     

    Air from the fan pressurizes the CCS tanks and delivers seed to the seed hoppers. Airflow enters the seed tanks through a nozzle in the manifold which pressurizes the tank. The air then picks up seed and moves out the other end of the nozzle into seed delivery hoses. These hoses route the seed toward the hopper. A small amount of seed is traveling in the delivery hoses only when needed.

     

    The hopper fills with seed until the delivery hose (discharge elbow) is covered. Once the opening is restricted, seed flow through the hose stops. Air flowing to the row unit travels into the hopper and is the source of air for the vacuum system. This provides a much cleaner air source than previous meter designs. As the seed is picked up by the meter and planted, the seed pool shrinks until the end of the delivery hose is uncovered. At that time, the airflow and seed delivery resume and the seed pool in the hopper is replenished.

    CCS seed cleanout

    Seed cleanout could not be much easier with a CCS Planter. When finished planting, any remaining seed can simply be removed via access doors at the bottom of the CCS tank.

     

    Because seed is only traveling through the CCS delivery hoses when required by the meter, there is not much left to clean.

     

    Next, CCS seed delivery hoses are then purged with air from the CCS fan and the excess seed is pushed to the individual meters.

     

    The vacuum meter door is opened and seed is removed with the supplied catch pan. 

    Small seed CCS components
    Manifold nozzle and nozzle with cover installedManifold nozzle and nozzle with cover installed
    Straight-seed inlet installed in mini hopperStraight-seed inlet installed in mini hopper

    CCS seed delivery system increases planting productivity across the seven approved crops listed above. While highly effective delivering seed from the CCS tanks to the vacuum meters, small or light seeds (sorghum and small cotton) will require two additional components to aid in proper seed delivery. 

    Manifold nozzle covers (clips) should be installed to ensure seed is adequately picked up into the air stream for delivery to the row-unit. Mini-hopper discharge elbows should also be changed from the standard elbow (holes) to the small seed elbow (slotted openings) when planting sorghum (milo) and small cotton. 

Drawbar hitch
    Drawbar hitchDrawbar hitch
    #

    A factory-installed, optional drawbar hitch is available for use with 1775NT 16- and 24-Row, 1775NT Central Commodity System (CCS™) 16- and 24-Row, and 40-ft 1795 Planters. For all DB models the drawbar hitch is in base. All DB models are available with Category 5 drawbar hitch. The following DB models are not available with Category 4 drawbar hitch: DB80 48R20, DB88 48R22, DB90 36R30, DB90 54R20, DB120 48R30.

     

    The planter drawbar hitch provides easy operation with plenty of ground clearance. The hitch design utilizes a hydraulic cylinder to raise the planter hitch for transport. Hydraulic oil for the hitch cylinder, on 1775NTs and 1795s, comes from the row marker system. Activation of this cylinder is accomplished using a single switch on the display and the marker selective control valve (SCV).

     

    Due to the hydraulic system design, the drawbar hitch requires the planter be equipped with independent markers (not tied to planter lift circuit). Removal of markers from all planters, except the 1775NT 24Row30, makes the drawbar hitch inoperable. The 1775NT 24Row30 is the only planter where the drawbar hitch, less markers, is a valid combination.

     

    For planting on 38-cm (15-in.) row spacing with a 16/32-Row 1795 Planter, the drawbar needs to be offset 19-cm (7.5-in.) on the tractor to center the planting rows behind the tractor. When the 16/32 1795 has a drawbar hitch, operators may not be able to offset the hitch to the exact specifications of 19-cm (7.5-in.) when planting in 38-cm (15-in.) operation, and could be off as much as a 1.3-cm (0.5-in.). To compensate, additional adjustments to the marker will be necessary.

     

    When using a guidance system such as parallel tracking or AutoTrac™ assisted steering system, operators will need to use their implement offset when planting with all rows on 1795 Planters equipped with the drawbar hitch to compensate for the offset.

     

    The drawbar hitch is ideal for those who have 9000 Series Tractors without a 3-point hitch. For these, the planter drawbar hitch is the economical choice instead of adding a 3-point hitch.

     

    To accept the planter drawbar hitch, the tractor drawbar must be ordered with, or upgraded to, a Category 4 drawbar with the heavy-duty package or Category 5 to be compatible. Track tractors with wide-swinging drawbars are not compatible with the planter drawbar hitch due to a lower hitch-load capacity.

     

    Each 1795 or 1775NT Planter ordered with the drawbar hitch will be shipped with a Category 4 hitch link installed. A Category 5 hitch link is also shipped with the planter if the planter is to be used with a Category 5 drawbar. See pre-delivery instructions included with the planter for changeover information.

     

    Compatibility:

    • Category 5 implement hitch links are not compatible with Category 4 tractor drawbars.
    • Category 5 tractor drawbars are not compatible with Category 4 implement hitch links.

      This hitch also adds 0.6-m (2-ft) to planter length during transport and field operation. There are some combinations of planter options that are not compatible with the drawbar hitch option due to tractor drawbar limitations.

Seed variable rate drive (VRD) with half- or three-width disconnect
    VRD shown on a 1775NTVRD shown on a 1775NT

    The seed variable-rate drive provides the ultimate planting productivity by utilizing one, two or three hydraulic motors (varies by model) to turn the seeding drive shaft. Hydraulic control of the seeding drive allows for on-the-go seeding rate changes right from the display mounted inside the tractor cab. 

     

    Combine this seeding flexibility with the map-based planting option, and seeding rates adjust automatically based on a prescription map.

     

    Single- or dual-motor systems for variable-rate drives are available for all John Deere planters except the 1785 Rigid Frame. Dual- or three-motor drive systems are commonly used on larger (12-row and more) planters and offer the capability of half-width or three-section drive disconnect.

     

    The VRD is available as a factory-installed option for all applicable planter models. Single- or dual-motor systems are available as field-installed attachments for most planter models; however, a three-motor VRD field-installed attachment is not available.

     

    The seed VRD requires the SeedStar™ monitor and a radar input signal. Either tractor or planter radar may be used. Planter radar is ordered separately.

    VRD offers the following advantages over common, contact-tire drive systems: 

    • Almost instantaneous rate changes; there is no ramp up or ramp down of system as in some competitive systems
    • Permits the operator to match seed population based on different soil types or irrigation practices
    • John Deere design that provides added operator safety by eliminating any possible drive creep found in some competitive variable rate drive systems
    Half-width drive disconnect

    The half-width drive disconnect feature is excellent for the producer concerned with controlling seed costs. This feature helps the operator place seed in the desired area and limit the amount of costly overlapped planting. 

     

    The half-width drive disconnect allows the operator to turn off half of the planter at a time for planting end rows, point rows, etc. Variable-rate-equipped planters require two drive motors to utilize the half-width disconnect feature. 

    Half-width drive disconnect within frame controlHalf-width drive disconnect within frame control

    With a 1765, 1765NT, and 1775 12-Row Planter, a single switch box is required for planters that are ordered with variable rate drive and half-width disconnect.

     

    For the 1775NT, 1775NT Central Commodity System (CCS™), and 1795 Front-Folding Planters, the half-width drive disconnect switch is contained within the frame control box, conveniently located in the tractor cab. The function easily shuts off the drive for the left or right half of the planter row-unit seed meters.

    Three-width drive disconnect
    Three-width drive disconnect controlThree-width drive disconnect control

    Three-width drive disconnect is an option on 1725 12-Row Planters and is base equipment on the 1725 16Row30 Planter. This feature is activated by three individual console mounted switches (control box), conveniently located in the tractor cab. The function easily shuts off the planter row-unit seed meters by one-, two-, or three-drive segments independently.

Downforce system options
    #
    Heavy-duty adjustable downforce springs
    Heavy-duty adjustable downforce springHeavy-duty adjustable downforce spring

    Planter row-unit downforce is an important factor to ensure consistent and proper depth control. The heavy-duty adjustable downforce feature provides up to 181.4 kg (400 lb) of downforce. There are four settings available to allow the operator to choose the amount of downforce required for the condition: 0 kg (0 lb), 56.7 kg (125 lb), 113.4 kg (250 lb), and 181.4 kg (400 lb).

    Compatibility: 1705, 1715, 1725, 1735, 1755, 1765, 1765NT, 1775 Flex, and 1785

    Standard pneumatic downforce system

    Pneumatic downforce provides convenient, simple adjustment of downforce for the whole planter from one location. The amount of downforce applied is infinitely adjustable from 0 to 181.4 kg (0 to 400 lb). Pneumatic downforce provides more consistent downforce throughout the range of row-unit travel than mechanical spring downforce systems.

    Features include:

    • 9.5-mm (3/8-in.) air delivery line instead of the 6.4-mm (1/4-in.) line used on model year 2010 and older planters.
    • Air compressor assembly increased duty cycle. With this compressor, it provides a 47 percent increase in maximum air flow delivery compared to the prior air compressor.
    • Pneumatic air bags with 9.5-mm (3/8-in.) air line inlets that have greater durability.
    SeedStar XP row-unit downforce planter run page
    SeedStar XP downforce planter run pageSeedStar XP downforce planter run page

    Active downforce control is integrated into SeedStar XP and SeedStar 3HP monitoring systems.

     

    Margin is the amount of weight riding on the depth gauge wheels that ensures desired firming of the seedbed as set by the operator.

     

    Once a target margin has been defined, enter the value into SeedStar XP or SeedStar 3HP and let active downforce do the rest. The system will actively adjust the air pressure in the air bags to maintain a constant margin across the planter. The changes in air pressure will change the amount of downforce placed on the row-unit, compensating and reacting for varying conditions through the field whether it is different tillage practices, soil types, or moisture.

    Pneumatic downforce springPneumatic downforce spring

    Each row-unit has a single rubber air bag located between the parallel arms. The air bags are hooked in parallel so that air can be added or released from all rows at once from one location.

     

    The individual pneumatic downforce air bag assemblies, air compressor units, and 9.5-mm (3/8-in.) delivery lines are also available as an attachment for field conversion.

    Pneumatic downforce compressor and gaugePneumatic downforce compressor and gauge

    An improved compressor is used to charge the pneumatic system. This compressor can be located on the planter frame or in the tractor cab if desired. A gauge at the compressor indicates the amount of downforce being applied.

    From the factory, integral planter models with pneumatic downforce will have an improved air compressor assembly with an in-cab mounting bracket, except for the 1725 16-row and 1725 Central Commodity System (CCS™ ) twin-row planters, which will have the air compressor assembly mounted on the planter frame. For drawn planter models, the 1755, 1765, 1765NT, 1775 Front-Fold, and 1785 Drawn Planters will have the air compressor assembly installed either on the outer hitch or wing frame members when the pneumatic downforce system is installed.

    Base equipment on: 1705, 1715, 1725, 1735, 1755, 1765, 1765NT, 1775 and 1785. 

    Integrated pneumatic downforce system

    The functional features of the integrated system are the same as the standard pneumatic system, explained above, with the addition of control through the GreenStar™ (GS) display.

    System control with the GreenStar (GS) display
    Pneumatic downforce control in GS2 DisplayPneumatic downforce control in GS2 Display
    Air compressor mounted on 1775NT outer hitchAir compressor mounted on 1775NT outer hitch

    On 1725 16-row, 1725 Central Commodity System (CCS™) TR, 1775NT, 1775NT CCS, 1795, DR, and DB Series Planter models, the air compressor will be mounted on the outer hitch or frame assembly. Since the air compressor assembly is mounted on the outer hitch (as noted in the picture above) or frame, adjustments for row-unit downforce and related system pressures will be made electronically with the GS display.

     

    When adjusting the amount of row-unit downforce using the GS display, the operator will select the amount of downforce (kg [lb]) to be applied across the planter. Depending on the soil conditions at hand, the operator might need to adjust the relative amount of row-unit downforce being applied during the planting operation. The integrated pneumatic downforce controls within the GS display will only allow for set-point operation and not automatic control as the planter is operating in different soil conditions. The pneumatic downforce system does not have the capability to automatically adjust downforce.

    On-board air storage
    Onboard air storage installed on 1775NT 24R30Onboard air storage installed on 1775NT 24R30

    The 1725 16-row, 1725 CCS TR, 1775NT, 1775NT CCS, 1795, DR, and DB Series planters will have onboard air storage to increase the overall response time when making a row-unit down force adjustment from the GS display. The onboard air storage is comprised of a 18.9-L (5-gal.) storage tank with valve assembly.

     

    Base equipment on: 1725 CCS, 1725 16-row, 1725T, 1775NT, 1775NT CCS, 1795, DR, and DB Series Planters with MaxEmerge™ 5 row units. MaxEmerge 5e and ExactEmerge™ equipped planters come with active pneumatic downforce in base.

    Active pneumatic downforce
    Active downforce compressor assemblyActive downforce compressor assembly
    Hydraulic motorHydraulic motor

    A hydraulically driven compressor works with the SeedStar™ 3 HP system and SeedStar XP system to automate downforce control. Just set the row-unit target margin value and the active pneumatic downforce system works automatically. The system will make sure the planter maintains this value, achieving precise soil penetration, and consistent planting depth, without sidewall soil compaction. From the factory, the system is set at 45.4 kg (100 lb) target downforce margin, but may be modified for varying field conditions. This frees the operator from constantly making manual downforce adjustments as conditions change.

     

    This system offers a split-rank control feature for 1795 and DB Split-Row Planters. On split row planters active downforce will control the front and rear rows independently. This compensates for differing downforce requirements between the ranks that can be caused by things like different tillage or insecticide attachments and will help maintain an accurate planting depth and consistent margin across all the rows.

     

    Active pneumatic downforce is available as factory installed or as an attachment for field conversion.

    IRHD screen showing the ground contact graphIRHD screen showing the ground contact graph
    IRHD screen showing the applied downforce graphIRHD screen showing the applied downforce graph

    Optional equipment on: 1775NT, 1795 and DB models with MaxEmerge™ 5e and ExactEmerge™ row units.

    Individual row hydraulic downforce (IRHD)
    #

    IRHD has been specifically designed to meet the needs of producers that are looking to adjust to the toughest field conditions and provide maximum yield potential from field to field, season after season. IRHD works as a closed-loop downforce system that reacts quickly on an individual row basis to changing soil conditions supporting increased ground contact, which can lead to improved seed depth consistency. When setting planter downforce margin, the system will apply the needed downforce by row to maintain ground contact. From the factory, the margin will be set at 45.4 kg (100 lb), changes may be required based on varying field conditions.

    The system allows operators to maintain gauge wheel ground contact leading to desired seed depth placement. IRHD can adjust five times per second and make adjustments of 45.4 kg (100 lb) in less than a second. The system has a total range of applied downforce from 22.7 kg (50 lb) to 204.1 kg (450 lb) and utilizes the power beyond circuit on the tractor. IRHD is 58 percent faster than the active pneumatic downforce solution. Fast reaction and increased ground contact can lead to improved emergence. With uniform emergence, some studies have shown a yield impact from 5 percent to 9 percent.

    IRHD is controlled through the Gen 4 4600 CommandCenter™ display or 4640 Universal Display with SeedStar 4HP. As shown below, operators can view ground contact or applied downforce using the toggle button.

    Down force and margin exampleDown force and margin example
    • A - Margin – amount of additional down force applied to a row unit above and beyond what is required for penetration to achieve planting depth. This additional weight will ride on the depth gauge wheels. 54.4 kg (120 lb) + 36.3 kg (80 lb) = 90.7 kg (200 lb) – 68 kg (150 lb) = 22.7 kg (50 lb) of margin
    • B - Weight of row-unit - 54.4 kg (120 lb)
    • C - Downforce – force that is applied to the row-unit by the air bag circuit - 36.3 kg (80 lb)
    • D - Resistance from soil - 68 kg (150 lb)
    Hydraulically-driven compressor
    Hydraulic motorHydraulic motor
    Pneumatic valvePneumatic valve

    The hydraulically-driven air compressor can deliver up to eight times the air flow, allowing for more and faster downforce changes to be made. This more robust design features a 37.8-L (10-gal.) storage tank across all models with active downforce.

    At approximately 15.1 L/min (4 gpm), hydraulic demands are low and ties into the machine’s lift and CCS hydraulic circuit so it does not require any additional selective control valves (SCVs). The SeedStar XP and SeedStar 3HP monitoring systems work with the compressor and valve assembly to regulate air to downforce springs, enabling the active control.

    Another feature of John Deere active downforce is the ability for the pneumatic valve to independently control split-rank machines. This system senses the downforce needs from the front and rear ranks separately and independently adjusts air pressures with the dual-rank pneumatic valve when equipped. Active pneumatic downforce requires SeedStar XP or SeedStar 3HP to enable active control.

    Base equipment on: All MaxEmerge™ 5e and ExactEmerge™ equipped planter models.

Innovative Central Insecticide System (CIS)

    The CIS is designed to work with Force® CS system, which is an improved soil-applied insecticide designed to deliver consistent performance in an advanced, convenient liquid formulation. 

     

    The innovative design of the CIS incorporates many user-friendly features such as closed handling, central fill, direct injection, and industry-leading row-to-row accuracy.  CIS is available on the following models with Central Commodity System (CCS™) equipped planters, and can be only ordered as an aftermarket field conversion attachment:

    • 1775NT CCS – 12 row
    • 1775NT CCS – 16 row
    • 1775NT CCS – 24 row
    • 1795 – 12/23Row and 12/24 row
    • 1795 – 16/31Row and 16/32 row
    • DB60 – 47 row 38 cm (15 in.)
    • DB80 – 32 row 76 cm (30 in.)
    • DB90 – 36 row 76 cm (30 in.)
    Force CS

    For more than 20 years, growers have trusted the performance of Force 3G for superior control of corn rootworms, as well as troublesome early-season pests.  Now, with Force CS, growers can achieve the same top-rated performance they have come to expect from Force 3G in an easier to use liquid formulation. Force CS will be packaged in a unique patent-pending box.  Each box contains 9.4 L (2.5 gal.) of Force CS and will treat approximately 16 ha (440 acres).

    System components

    The CIS consists of six major components:

    1. Insecticide cabinet
    2. Water tank(s)
    3. Pump and valve assembly
    4. Flow monitors
    5. Nozzles
    6. Controller/monitor
    Insecticide cabinet
    Insecticide cabinet - loaded with Force CSInsecticide cabinet - loaded with Force CS

    The insecticide cabinet, which is manufactured from the same material as the CCS tanks, is designed to hold a maximum of eight boxes of Force CS. Each Force CS box contains 9.4 L (2.5 gal.) of product for a total system capacity of 76 L (20 gal). This 76 L (20 gal.) of Force CS allows the operator to cover 256 acres between fills if the full rate (10 oz/acre for 76-cm [30-in.] rows) of Force CS is applied for all rows. The coverage acres increase if product is only applied to the designated refuge rows.

    Connectors and in-line check valveConnectors and in-line check valve

    After the desired number of Force CS boxes are placed in the cabinet, the operator connects the Force CS box to the CIS system by using a connector (shown on the left). This connection device drastically reduces the amount of exposure compared to granular-type insecticide systems.

     

    The system is also designed to empty the boxes from the top down. Product from the top boxes will empty before the system starts to pull product from the next row. This is possible by utilizing a check valve on the last product box (shown on the left).

    Flow monitors
    Flow monitorsFlow monitors

    Flow monitors are mounted on the wings to provide operator confidence and peace of mind that each row is receiving an equal amount of product.  When operating, the orange balls within the flow monitors will be suspended in the middle of the site glass.  If a nozzle or delivery line becomes restricted or becomes damaged, the flow monitor will indicate this under or over application.

     

    Water tank
    1135.6-L (300-gal.) tank on 1775NT 16Row1135.6-L (300-gal.) tank on 1775NT 16Row

    The CIS utilizes direct injection technology to move ounces of the Force CS product into water; therefore, every CIS requires an appropriately sized water tank to supply the pump and valve assembly for Force CS application. Below is a chart with planter model, tank sizes, and acres covered.

     

    Planter model

    Water capacity

    Acres/fill (water)

    Acres/fill (insecticide) eight-box cabinet

    Rate = 2 gal./acre

    Rate = 10 oz/acre

    9.1-m (30-ft) 1795

    852 L (225 gal.)

    46 ha (113 acres)

    104 ha (256 acres)

    12.2-m (40-ft) 1795

    1060 L (280 gal.)

    57 ha (140 acres)

    104 ha (256 acres)

    12-row

    1775NT CCS

    852 L (225 gal.)

    46 ha (113 acres)

    104 ha (256 acres)

    16-row

    1775NT CCS

    1136 L (300 gal.)

    61 ha (150 acres)

    104 ha (256 acres)

    24-row

    1775NT CCS

    1703 L (450 gal.)

    91 ha (225 acres)

    104 ha (256 acres)

    DB60

    1590 L (420 gal.)

    85 ha (210 acres)

    104 ha (256 acres)

    DB80

    1590 L (420 gal.)

    85 ha (210 acres)

    104 ha (256 acres)

    DB90

    1590 L (420 gal.)

    85 ha (210 acres)

    104 ha (256 acres)

    NOTE: Depending on model, water capacities may be reduced when equipped with Refuge Plus™ system.

    Pump and valve assembly
    Pump and valve assemblyPump and valve assembly
    Three-section valvesThree-section valves

    The pump and valve assembly consists of a hydraulically driven water pump, electric injection pump, and section valves. The hydraulic water pump is tied into the frame hydraulics and does not require an additional selective control valve (SCV). The electric injection pump pulls product out of the Force CS boxes and injects the product into the waterline, which then enters a mixing chamber where the water and Force CS are thoroughly mixed together. 

     

    The CIS system features a closed calibration procedure to protect the operator from insecticide exposure. Comparable granular type insecticide systems require the operator to collect chemical from each row-unit on the planter, while the CIS closed calibration is performed at one central location and does not require the operator to measure any product, dramatically eliminating exposure to insecticide.

     

    One of the many features of the CIS is the ability to apply insecticide on refuge rows only. From the tractor cab, the operator can set the monitor to apply insecticide to refuge rows only. This makes the CIS a perfect fit with Refuge Plus.  When refuge only is selected on the monitor, the CIS will only apply insecticide on the designated refuge rows. These rows are predetermined from the factory and are listed below for each model.

     

     

     

     Model Refuge rows

     1775NT CCS - 12row

     10, 11, 12
     1775NT CCS - 16row 13, 14, 15, 16
     1775NT CCS - 24row 20, 21, 22, 23, 24
     1795 - 12/23row 19, 21, 23
     1795 - 12/24row 20, 22, 24
     1795 - 16/31row 25, 27, 29, 31
     1795 - 16/32row 26, 28, 30, 32
     DB 60 20, 21, 22, 23, 24
     DB 80 14, 15, 16, 17, 18, 19, 20
     DB 90 15, 16, 17, 18, 19, 20, 21, 22

     

    While the ability to apply Force CS to refuge rows is a unique feature, CIS can easily distribute product to every row across the entire planter width.  Application setup is simple and is completed through the system monitor/controller.

    Nozzles
    NozzleNozzle

    The CIS system utilizes a 0067 SprayMasterTM nozzle to apply the Force CS in 13- to 20-cm (5- to 8-in.) T-band over the seed furrow.  This nozzle is located between the double disk openers and the closing wheels.  When not in use, a nozzle cap is provided to replace the nozzle protecting it from wear. 

     

    Applying Force CS in a T-band pattern is the only approved application method.  Spraying the product in a T-band ensures proper application and seed/soil coverage.  The supplied 0067 SprayMaster nozzle is not compatible with any length of aftermarket seed firmer due to spray interference.  If the planter is equipped with short seed firmer, a separate flat fan nozzle and adapter should be used. 

    Monitor
    CIS monitorCIS monitor

    CIS utilizes a separate, independent monitor that also acts as the system controller.  The monitor is capable of controlling two separate products at the same time (water and Force CS) and is compatible with GreenStar™ (GS) 2 Field Doc™ connect.  This monitor is specific to the CIS and will not work with any other applications. 

     

    The monitor conveniently displays product application rates, acre totals, and product/acres remaining.  System setup, product and water rates, as well as priming are initiated from the controller/monitor.  CIS is completely integrated with the planter design.  CIS automatically shuts off product flow when the planter is raised and is also tied to the seed meter one-half or one-third width disconnect.

    IMPORTANT: Always read and follow label directions before buying or using this product.  Force CS is a restricted-use pesticide. 

    Force® CS is a trademark of a Syngenta Group Company.

    System cleanout

    CIS end-of-season cleanout and winterization is simple to perform.  CIS will draw John Deere winterizer fluid (part N305643 or equivalent) through the system and residual Force CS with winterizing fluid solution will be captured in an enclosed container for proper disposal.  Follow all label instructions for proper handling and disposal procedures. 

Row cleaner options to meet residue management needs

    Crop yields have increased through the years along with the amount of residue left in the field after harvest. At the same time, tillage practices have changed, including different tillage operations which maintain large amounts of surface residue, and even no till practices. Row cleaners are an essential tool in managing this increased amount of residue.

     

    John Deere seeding group offers a variety of row cleaner options to meet the needs of a producer's operation. Compatibility varies by model, row spacing, and other planter equipment.

    Screw-adjust unit-mounted row cleaner
    Screw-adjust unit-mounted row cleanerScrew-adjust unit-mounted row cleaner

    The screw-adjust unit-mounted row cleaner is mounted directly to the face plate of the row-unit, placing the ground engaging components just in front of the row-unit opener blades and depth gauge wheels. This close proximity allows the gauge wheels to control the depth of the row cleaner as well as the row-unit. This compact design also allows greater compatibility with fertilizer openers and other planter attachments.

     

    SharkTooth® wheels are standard equipment on the unit-mounted row cleaner. The swept-tooth design of the wheel provides a clear path for the row-unit openers while resisting residue buildup on the wheel. The screw adjustment knob is accessible through the top of the parallel arms, providing convenient access for adjustments. The row cleaner can be adjusted in 1.6-mm (0.06-in.) increments, providing plenty of flexibility to meet the needs of changing conditions.

    Floating row cleaner with unit-mounted coulter
    Floating row cleaner with unit-mounted coulterFloating row cleaner with unit-mounted coulter

    The floating row cleaner allows a row cleaner to be used in conjunction with a unit-mounted coulter. This combination is often desired in heavy residue loads and tough reduced tillage planting conditions. The row cleaner provides a clear path for the row-unit, while the unit-mounted coulter helps penetrate tough soil conditions.

     

    Accommodating the unit-mounted coulter means the residue wheels are farther forward from the row-unit face plate than in the case of the screw adjust row cleaner. To maintain performance, this row cleaner has the capability to float above a defined minimum depth.

     

    Standard depth-gauging bands on the wheels allow the row cleaner wheels to float independently of the row unit openers, allowing both to perform in varying terrain. The unit may also be set in a fixed position by simply pinning through the bracket if desired. This row cleaner also features SharkTooth wheels as standard equipment.

     

    The floating row cleaner and unit-mounted coulters are available on many planters as factory-installed equipment. As compatibility and details vary by model, review the following links for information on specific planter models.

    SharkTooth is a trademark of Yetter Manufacturing.

     

    NOTE: Screw-adjust row cleaners are not compatible with MaxEmerge™ 5e row-units with long parallel arms.

     

    NOTE: DB models have the option for either unit-mounted coulter, screw-adjust row cleaners, or pneumatic row cleaners (only compatabile with MaxEmerge 5e or equipped ExactEmerge™ models). The DB60T is only available with less row cleaner option.

Provide added versatility and productivity with Central Commodity System (CCS™) Refuge Plus™ planter configuration
    #

    DB44, DB60, DB60T, DB66, DB80, DB88, DB90, and DB120 Planters can be equipped with the Refuge Plus option from the factory.

    The third tank on the Refuge Plus system provides increased versatility and productivity to the planting operation by allowing the grower to plant two different varieties simultaneously. The Refuge Plus tank has manifold nozzles, or outlets, to supply seed to eight different row-units.

    Refuge Plus is ideal for the grower planting Bt corn or seed corn. Refuge Plus is the solution for refuge management compliance issues associated with Bt corn production. The 880-L (25-bu) capacity of the third tank makes planting the required 20 percent refuge of non-Bt corn easier while maintaining high productivity levels of the central-fill CCS.

    For example, Bt corn planted on 80 percent of the field goes into the larger CCS tanks. The required 20 percent refuge, non-Bt corn, goes into the third Refuge Plus tank with the seed hoses routed to the desired rows.

    Central fill with CCS is easier for the seed-corn grower as well. The seed-corn grower can plant both male and female seed in the desired pattern simply by placing the male seed in the Refuge Plus tank, the female seed in the CCS tanks, and routing the seed delivery hoses to the desired row units.

    NOTE: Only DB44, DB60, DB60T, DB66, DB80, DB88, DB90, and DB120 Planters can be equipped with the Refuge Plus option from the factory. Other CCS equipped models can add Refuge Plus through parts.

    Redirecting seed delivery
    Seed delivery hose connection and yellow plugSeed delivery hose connection and yellow plug

    Redirecting seed delivery from the CCS tanks to the Refuge Plus tank is fast and easy with quick-disconnect couplers. By simply disconnecting the desired CCS delivery hoses from beneath the CCS tank, capping those hoses and reconnecting the delivery lines to the Refuge Plus tank, the seed delivery source is changed.

    Due to the additional weight Refuge Plus places on the planter frame, liquid fertilizer tanks are not compatible. Updated liquid insecticide tank codes have been established for Refuge Plus planters.

SeedStar™ XP monitoring system
    SeedStar XP overview
    SeedStar XP shown on the GreenStar 3 2630 DisplaySeedStar XP shown on the GreenStar 3 2630 Display
    SeedStar XP shown on the GreenStar 2 1800 DisplaySeedStar XP shown on the GreenStar 2 1800 Display

    Building upon the foundation of SeedStar 2, the SeedStar XP system takes planter monitoring to the next level. When paired with the GreenStar™ (GS) displays (GS 2600 or 2630 Display or the entry-level GS2 1800 Display), the SeedStar XP monitoring system provides more information about the planting process to the operator within the tractor cab.

     

    Specific information about how the planter is performing enables the operator to make needed adjustments for implement optimization.

     

    The SeedStar XP planting functions are fully integrated with the full spectrum of AMS applications such as Swath Control Pro™ system for planters, GreenStar AutoTrac™ assisted steering system, John Deere Operations Center, documentation, and others. Integrated planting technologies, for better asset utilization and ease of use, is just part of what SeedStar XP provides.

    SeedStar XP seed singulation monitoring
    SeedStar XP seed singulation planter run pageSeedStar XP seed singulation planter run page

    Understanding the meter singulation performance on the planter is critical to minimizing the amount of seed multiples and skips. As a result, the SeedStar XP monitoring system provides real-time information from the row-units about the overall seed singulation performance.

     

    As seen in the screen shot image above, seed multiple information is displayed on the top portion of the planter-at-a-glance bar with seed skip information on the lower portion. This provides the operator a better understanding of relative seed multiple and skip data on a row-unit basis; all within one easy glance.

     

    Also, within the seed singulation planter run page, information about row-units with the highest percentage of seed multiples and skips is provided in order to make necessary adjustments for better planter optimization.

    SeedStar XP row-unit ride dynamics planter run page
    SeedStar XP ride dynamics planter run pageSeedStar XP ride dynamics planter run page

    While operating a planter, travel speed and field conditions can affect the amount of row-unit bounce that is experienced. Excessive row-unit bounce or vertical motion can cause problems with meter performance. To better understand the amount of row-unit vertical motion when travelling through a field, the SeedStar XP monitoring system provides real-time information on row-unit ride dynamics.

     

    As seen in the ride dynamics planter-at-a-glance screen shot image above, the SeedStar XP system provides ride dynamic information for each sensor node that is mounted on the planter. Each sensor node transmits ride dynamic information for each planter frame section to allow for the operator to make necessary operating adjustments to improve overall planting performance.

    Downforce sensor installedDownforce sensor installed
    Downforce sensor assemblyDownforce sensor assembly

    Depending on the planter size, different configurations of sensor nodes and downforce sensors are installed in support of the SeedStar XP monitoring system.

    SeedStar XP row-unit downforce planter run page
    SeedStar XP downforce planter run pageSeedStar XP downforce planter run page

    As row-unit downforce systems gradually change from heavy-duty downforce springs to pneumatic downforce, being able to understand the amount of as-applied row-unit downforce is needed while operating the planter.

     

    With various soil conditions, moisture, etc. experienced while planting, it is imperative to have the ability to change actual row-unit downforce to have enough force for the Tru-Vee™ openers to penetrate the soil media. However, in some conditions, having too much downforce applied to the row-units for effective opener penetration could cause problems with side wall compaction from the gauge wheel.

     

    Side wall compaction within the seed furrow can cause hatchet roots to develop; or roots that do not have the ability to penetrate the seed furrow soil media. This could lead to poor plant emergence and eventually lower overall yield performance.

     

    With the SeedStar XP monitoring system, row-unit downforce information is measured by the downforce sensor and sensor nodes and transmitted to the GreenStar 2 (GS2) Display in the tractor cab (as seen in the image above). The row-unit downforce information is displayed on the top portion of the planter-at-a-glance bar with more row-unit downforce information on the lower portion.

     

    Two different control options are available on 1775NT, 1795, and DB Series Planters for pneumatic downforce. The base pneumatic downforce system requires manual control of the downforce to maintain the desired planting results or row-unit margin. Optional active pneumatic downforce takes SeedStar XP even further by removing constant downforce adjustments from the operator and actively controlling the downforce system to maintain a desired target margin.

    SeedStar XP seed spacing monitoring
    SeedStar XP seed spacing planter run pageSeedStar XP seed spacing planter run page

    Throughout the planting process, obtaining good seed spacing is critical toward achieving plant growing conditions for maximum yield potential.

     

    Today, many items are adjusted on the planter prior to planting to optimize overall seed spacing performance. After such adjustments are made, information about the actual seed spacing performance during planting was missing within the planter monitoring system. Now with SeedStar XP, seed spacing information is transmitted live via the GreenStar display to show the operator exactly what is happening with the planter behind them.

     

    The SeedStar XP transmits seed spacing information onto the planter-at-a-glance bar for easy understanding of planter seed spacing performance. Also, information about seed skips and multiples is provided to help understand actual planter meter performance and other related system functions in order to make necessary adjustments if needed.

    NOTE: Seed spacing and seed singulation information is only available when planting crops with seed drop rates below 40 seeds/second such as corn. With higher population crops such as soybeans the system does not provide spacing and singulation information because the number of seeds dropping per second is much higher.

    SeedStar XP full planter performance page
    SeedStar XP planter details SeedStar XP planter details

    With the capability of monitoring differences in planting performance items such as seed singulation and row-unit downforce, having one screen to view all planter performance elements is needed to understand the whole planting system. SeedStar XP combines all of the various planting performance elements into one full-color, planter overview screen to enable for a quick understanding of relative planting functionality.

    SeedStar XP half screens and other features
    SeedStar XP seed singulation half screenSeedStar XP seed singulation half screen
    SeedStar XP seed spacing half screenSeedStar XP seed spacing half screen

    Other SeedStar XP monitoring features include:

    • Capable of monitoring individual row-unit and overall planter performance in terms of seed spacing, singulation, and row-unit downforce
    • Split-screen applications to enable use of popular guidance features such as AutoTrac™ assisted steering system
    • On-screen indication of sensor node/downforce sensor assemblies once configured within the monitor settings application
    • Full-color display icons for easy recognition and overall aesthetics
    • Pneumatic downforce system controls with the GS Display application
    SeedStar 2 monitoring original features

    SeedStar XP retains all of those SeedStar 2 features that producers value and have come to expect:

    • Planter-at-a-glance. Allows operator to view relative population levels of all rows on one screen.
    • Automatic valve calibration. With the SeedStar variable rate drive (VRD), this is now completed automatically. There is no longer a need to manually calibrate the hydraulic valves.
    • Increased population updates. SeedStar will now update population levels once per second at planter start up then approximately once every three seconds.
    • Mapping of actual seed rates. When combined with documentation, actual and target seeding rates can now be mapped in John Deere Operations Center.
    • Reprogrammable utilizing controller area network (CAN) via Service ADVISOR™ diagnostics system.
    • Improved diagnostics/event recorder. On SeedStar variable-rate drive (VRD) planters, additional diagnostic information is available, as well as an event recorder to capture system performance data at a specific point in time.
    • Ability to run motors at different population levels. On SeedStar VRD, operators running multiple motor systems can run each motor at a different speed, allowing different population levels within a planter.
    • User-configurable high fertilizer pressure alarm. Allows the operator to be warned when fertilizer pressure reaches a specific level.
    • Automatic quick-start for SeedStar VRD. No longer does the operator need to press the quick-start button on end row turns to resume planting.
    • Automatic tractor speed source selection. When equipped with an 8000/9000 Series Tractor, the system selects the radar speed or allows for manual speed input selection.
    Components and operation
    Planter main 2 controllerPlanter main 2 controller
    Sensor node assembly installedSensor node assembly installed

    The SeedStar XP monitoring system contains the following components in order to support the planting data transfer to the GS2 Displays:

    • Seed monitor/variable-rate (SMVR) controller with model year 2011 or newer software
    • Planter main 2 controller (installed on all SeedStar XP eligible models for model year 2011 or newer)
    • Sensor node(s)
    • Downforce sensor assembly

     

    The planter main 2 controller processes the row-unit data from the sensor node assemblies located on the row-unit head casting. The processed information is then sent to the SMVR controller to be integrated into the displayed information being sent to the GS Display.

     

    Downforce sensor assemblies are found on row-units with sensor nodes installed. The downforce sensor assembly is assembled with the gauge wheel depth-adjustment handle and provides gauge wheel pressure information to the respective sensor node for data processing.

Double eliminator - MaxEmerge™ 5 vacuum seed meters
    Double eliminator installed in MaxEmerge 5 meterDouble eliminator installed in MaxEmerge 5 meter
    #

    For difficult to singulate seeds, a flat seed disk and double eliminator is a viable alternative to traditional cell-type seed disks. By design, a flat seed disk requires higher levels of vacuum than a cell-type disk because there is no pocket or cell to hold the seed. The higher vacuum level will pull more than one seed to the holes in the seed disk. The double eliminator is set to cover a portion of the hole in the seed disk and is the mechanism to knock multiple seeds away as the disk rotates. 

     

    Double eliminators are required with flat-type seed disks only and should not be used with cell-type seed disks. The knockout wheel is also recommended in conjunction with the double eliminator and flat seed disk to ensure seed is ejected from the disk.

    Double eliminator adjustment
    MaxEmerge double eliminator adjustment knobMaxEmerge double eliminator adjustment knob
    Double eliminator numbered dialDouble eliminator numbered dial

    The MaxEmerge 5 vacuum meter has an external, adjustable double eliminator. This double eliminator uses a knob with numbers to indicate where it should be set for different crops. This feature makes achieving a high level of singulation easier and more consistent.

     

    The adjustment knob is capable of 21 unique positions. The dial is numbered zero through ten in increments of one, but the gearing allows for half increment adjustments as well.

     

    Adjustment time for this double eliminator is estimated to be 10 seconds per row-unit, with repeatable results. This means that adjustment can be made three times faster than Pro-Series XP™ units, and eight times faster than MaxEmerge XP units.

     

    Because flat seed disks require higher vacuum levels, planters with 12-row units or more require two vacuum blower motors. In addition to vacuum blower requirements, 0-cm to 76.20-cm (0-in. to 30-in.) mechanical vacuum gauges would also be needed to monitor the elevated vacuum.

Mexico

573-581-5900

Macon

660-385-2177

Rocheport

573-446-3030

Kirksville

660-665-1500

Chillicothe

660-646-5493

Palmyra

573-769-2112

Moscow Mills

636-366-9400

Curryville

573-594-6493

Tipton

660-433-5596

Hermann

573-486-3204

Dutzow

636-433-2256

SALISBURY

660-388-6166
Your Partner In Growing A Better Tomorrow
ABOUT USCONTACT US | CAREERS | BLOG | SPECIALS | SITEMAP | POLICIES | DONATION REQUEST |
AG EDUCATION PARTNERSHIPS | EQUIPMENT TRANSFER REQUEST


Copyright ©2017 Sedona Technologies. All rights reserved.